Advancenin

Vag k line + can commander 1.4, 3.6, 5.1,5.5 software Download

VVDI2 – VAG User Manual 12 Ver: 1.1 4.3. Coding Set target unit coding, we have database for most of the module, you can change coding by select item (PICTURE 4.4) (PICTURE 4.4) 4.4. Actuator test Test every small actuator in target unit, UDS protocol support selective tests, other protocol.

Vag k line + can commander full is obd2 usb diagnose interface for vag group cars. OBD2Tuning Vag K+Can Commander interface including K line Vag K+Can Commander 1.4, 3.6, 5.1, 5.5. Below OBD2Tuning sharing Vag k line + can commander full 1.4, 3.6, 5.1,5.5 software, free download.
VAG K+CAN Commander 1.4 full version VAG Commander v1.4
Vag k line + can commander full software, free download:
Vag k can commander 1.4 software download link:
http://yunpan.cn/QpEgG6Q99sBN8
VAG CAN Commander 5.5 software download link:
http://yunpan.cn/QpEgzuPpiBtJ9
VAG K+CAN Commander 3.6 software download link:
http://yunpan.cn/QpEgILdpH5d3K
VAG CAN Commander 5.1 software download link:
http://yunpan.cn/QpEgTHAzejYeI
K-Line VAG K+CAN Commander support full Diagnostic via CAN-und Special-Function via K-Line.
Vag k line + can commander full software Instructions guide:
1. Install the USB drivers for the vag k+can commander USB diagnose interface.
2. Verify the port settings.
3. Download and install the vag k+can commander software.
4. Configure and run Vag k line + can commander software.

Vag K Can Commander 1.4 User Manual

Vag Can Commander 1.4 Manual

VAG-K+CAN Commander 1.4 Installation Guide

Vag K+can Commander Full 1.4 User Manual

Vag K+can Commander Full 1.4

VAG K+CAN Commander is obd2repair diagnostic interface for vag group. VAG K+CAN Commander Full Diagnostic via CAN-und Special-Function via K-Line. Do you know how to install VAG-K+CAN Commander 1.4?

VAG K+CAN Commander 1.4 VAG K+CAN 1.4 Commander
Here OBD2Repair share with you VAG K+CAN Commander Full VAG-K+CAN Commander 1.4 Installation Guide.
1. Driver installation
1.1. Donlgle Driver -> in folder 'Dongle Driver USB' start file 'inf_inst.exe'
1.2. Interface USB driver -> in folder 'Interface Driver USB/Executable' start file 'CDM_Setup.exe'
2. Software installation
place folder 'VAG-K+CAN Commander' at usful for you place
3. Connect USB dongle to your PC
4. Connect interface to your PC
5. If your operation system is Windows XP - skip this step
Check proper setting of the USB-COM port
Your interface is detected from Windows like COM port (USB-COM).
You must check whether setting of CURRENT port are proper.
From 'My Computer->properies->hardware->device manager->Ports (COM&LPT)->USB Serial Port (COM x)'
select properties (right mouse button) then 'Port Settings->Advanced'. Your value for 'Latency Timer (msec) should be 1!
If not set to 1. You can have a look in the file 'advanced settings usb-com port.bmp' how seems settings.
NOTE: Next time when you connection your interface to another USB port settings above must be repeated so recommended is fisrst time when you starting usage to set proper setting of for all possible USB ports.
In the next SW releases need from setting of ports will be skiped.
6. Starting SW
You can start 'VAG-K+CAN Commander.EXE' file from folder mentioned in step 2. above.
Now your VAG K+CAN Commander is ready for use.